Rolleramic Wiring Diagrams
Conduit
connection
L = W+24" (through 12' x 12')
L = W+30" (over 12' x 12')
Through 12' x 12' 14¾"
Over 12' x 12' 21¼"
Access
Door
Bottom board
Case
¾" thick
4" - 4
1
/8"
Opening for fabric
Bottom
Front
Fabric width – W
Screen
surface
4
5
/8"
9
1
/
8
"
9
1
/8"
9
5
/8"
9
5
/8"
11
1
/2"
1"-6" from
access door
6"-12" from
case edge
Page 2 of 2
Case Dimensions
Rolleramic by Draper
Rolleramics over 12' x 12'
have a blue wire lead
instead of a black wire lead
coming from the motor.
Single Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Red (Down)
Black, or Blue (Up)
Green (Ground)
Dashed wiring
by electrician
Control
switch
Single gang box by others
Min. 4" x 2 1/8" x 1 7/8" deep
Blue
Black
Red
Location of key
operated on-off
switch if furnished
To 110-120V Line
Multiple Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Red (Down)
Black, or Blue (Up)
Green (Ground)
Dashed wiring
by electrician
Red
Red
Black
Blue
Blue
Cap off with wire
nut and tape
Black
Red
Blue
Black
Single gang box by others
Min. 4" x 2 1/8" x 1 7/8" deep.
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
For suspended mount
For wall mount
6
3
/
8
"
1
3
/
8
"
Rolleramic Mounting Bracket
.draperinc.com
(765) 987-799
Two-Way Serial Communication
(RS232) with MC1
See separate Serial Communication-
RS232 Instruction sheet for enabling
RS232 with the MC1.
3 Button Wall Switch
DOWN - Red
COM - White
UP - Black
White-Common to screen & 110-120V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Ye llow-to 110-120V AC-Hot
Black-to 110-120V AC-Hot
Green-Ground
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
Dashed wiring by electrician
Low voltage wiring by others
White (Common)
Red (Down)
Black (Up)
Green (Ground)
Location of key
operated on-off
switch if furnished
To
110-120V
Line
STOP
Control
Switches
24v DC
STOP
Low Voltage & Wireless Control
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Up
Manual Switch Down
White-Common to screen & 110-120V AC Neutral
Red-to Screen (directional)
Brown-to Screen (directional)
Black-Hot to 110-120V AC
Green/Yellow-Ground
Fuse
Program LED
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
Low Voltage Wiring by others
AC Wiring by electrician
MC1
White (Common)
Red (Down)
Black (Up)
Green (Ground)
Internal Screen Wiring
Location of key
operated on-off
switch if furnished
To
110-120V
Line
STOP
Control
Switches
STOP
Please Note: Mount the case using the two end brackets first. If
a center bracket is provided, mount it last. The center bracket is
designed to prevent sagging of the case, and must be mounted so
that it is level with the others and does not force the screen case
up. Make sure the top of the screen case's bottom board at no
point touches the roller/viewing surface.
Screens through 14' wide have 2 mounting
brackets; wider screens have 3. Brackets
should be located along case to line up
with supporting beams or studding. Motor
end bracket must be located 1"-6" to right
of access door. Idler end bracket must
be located 6"-12" from right end of case.
Failure to mount brackets as directed could
cause case to bow and result in damage
to screen.
Please Note: Do not wire motors in parallel.
(2 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji